Category :
Essential tools for woodworking
Monday, January 07, 2013
When we worked on our
first ever center table (which is also our first ever project), we had to stick a 4 mm sheet of One Side Team onto a plywood using synthetic resin glue. Because we had no means to hold the
OST sheet in place and the glue required some drying time,
we literally had to sit on either side of the table for a good 15 minutes. And we did this for the next few projects too. When it was a smaller work, like a DIY photo frame, I had to hold the sticks tightly together for a while before I was convinced that the glue has dried.
That is when I thought I should get my hands on C-Clamps
(also called G-Clamps), purely for my
gluing needs.
 |
| C-Clamps / G-Clamps |
Clamps are
wonderful tools for holding things together steadily in place while you are trying to work on them. Whether it is for gluing two surfaces together or to nail them, the
clamps come in handy to provide that firm grip which might otherwise not come from even steady hands. The clamps come in different sizes and it is important that you choose those that fit your needs.
I went for the smallest of ones that can open as wide as 1 inch and not more. Highly suited for surfaces of lesser thickness. I have ever since used these clamps successfully for
making a wall clock and for
laminating wooden surfaces.
 |
| C Clamps for basic woodworking and DIY needs |
I bought these clamps at Home Depot during my short visit to the US last year. I have also inquired here and these are available in hardware stores and tools shops. There are different types of clamps that are available and C-Clamps are just one of those. It has been an important accessory in my tool kit that has helped reduce the pressure on my fingers and deserved a special mention here.
Do you use clamps for your projects ? I believe they are extensively used even outside of woodworking. If you do use them for your crafting needs, share the details in the comments section. Will certainly love to hear about it.
- Somu
Monday, July 23, 2012
All these tools were bought on a need basis as and when I required them for a specific purpose. These tools largely serve your basic DIY woodworking needs and will certainly help you make those little projects around the house. (Note: This is a repost)
Safety is of prime concern and so you should take necessary precautions. If certain tools need supervision or you are not sure of their application, try to get it done through professionals. Better safe than sorry.
|
 |
| Woodworking hobby tools - Electric Drill |
Electric Drill
This is certainly a must have tool in the house if you are a DIY lover. It helps serve multiple needs. Be it hanging a painting on the wall, or making a center table, it is the electric drill that paves way by creating that much needed pilot hole. I have used this to install cabinet doors too. The one I use costed me about Rs.700 and comes with very basic features of single speed and clockwise rotation.
Associated Drill bits
The following are the drill bits that I bought over a period of time. All of these cost between Rs.10 to Rs.30 if you buy them separately.
· Masonry bit for drilling into concrete / brick walls
· Flat wood bit which I used as a counter sink bit
 |
| DIY Woodworking tools |
Claw Hammer
The use of a hammer is quite obvious. Since the only nails I use are the headless nails, I use the hammer mostly for pounding them into the piece of wood. You can use the claw to pull out any nail or screw.
Oh ! Did I tell you that it doubles up as a kitchen accessory? I use it to break coconuts.
Cutting pliers
I use them for holding the nails in place when I am hammering them into wood. Helps protect my fingers from being smashed. I also use them to strip off the plastic sheath from the wires while installing my DIY lampshades.
Screw Driver Set
Again another useful tool to have inside the house. Not just for the purpose of woodworking, but also for other requirements at home, these are very helpful. A kitchen hinge that is loose, a glass door that needs installation or a key holder that is not in place can be easily fixed. The entire set costed me only Rs.80.
 |
| More tools |
Wood Rasp
I remove all the sharp edges in my work using the Rasp. It helps give a slight curve to the edges. For the cabinet door that I installed, I used the rasp to give the edge a half round shape.
Measuring tape
Your projects will never have the symmetry you desire if not for the measuring tape. Sometimes even a couple of mm offset can make your project look awkward and so it is essential you get used to using the tape accurately. Sometimes it is also needed that you are able to quickly shift between mm and inches as the unit of measurement depending on the situation.
L Square
Perfect tool for drawing right angled vertical and horizontal lines.
Hacksaw blade
Serves all my cutting purposes. Again, the wood that I decide to cut is always of minimal thickness for which the hacksaw is very ideal. Not really suited for cutting wood that is beyond 6 mm in thickness. Not that it is impossible, but really makes it difficult to get that clean cut.
Mica / Laminate cutter
If you work regularly with Mica or laminate, this is a very useful tool. I also use it extensively for cutting 4mm One Side Teak sheet. Beyond 4 mm, this tool is ineffective for cutting.
So that’s about the handtools (with the exception of power drill) that I use. All my projects have been built using these basic tools. Will keep adding more tools and accessories to this list in due course.
What are your favorite tools ? I am not referring to just the ones you use for Woodworking. What are the tools that you use for your arts and crafts projects too ? Share your thoughts.
You may also be interested in:
Linking in :
Colours Dekor
